![\"\"](\"http:\/\/morinc.com\/wp-content\/uploads\/2019\/01\/lexmark.jpg\")
<\/p>\nLexmark Error Codes<\/p>\n
<\/p>\n
<\/p>\n
Error code
\nError code meaning
\nError 20
\nSensor on input tray not activated \u2013 could be a jam near the sensor.
\nError 21
\nSensor on output tray not triggered.
\nError 23
\nPaper jam near the duplex sensor.
\nError 24
\nJob not formatted correctly for the paper being used.
\nError 25
\nSensor on input tray triggered at the wrong time.
\nError 26
\nTray of duplexer not being recognized.
\nError 27
\nLoaded paper or envelopes are the wrong size.
\nError 28
\nInput rollers not picking up paper, not triggering sensor.
\nError 29
\nSensor on output tray has stopped.
\nError 30
\nToner cartridge not installed or cover is open.
\nError 31
\nCartridge detected and ID read, but it did not pass verification.
\nError 32
\nIncorrect cartridge installed.
\nError 37
\nMemory full, cannot collate the task.
\nError 38
\nMemory used to store pages sent to printer is full.
\nError 39
\nJob too complex for memory.
\nError 43
\nFont card not supported.
\nError 44
\nDefective font card.
\nError 47
\nFont card removed during task, data required to finish printing.
\nError 52
\nFlash memory is full.
\nError 53
\nDefective or unformatted flash memory.
\nError 54
\nSerial error.
\nError 58
\nDuplex unit is not attached.
\nError 59
\nDuplex unit cover is opened.
\nError 62
\nNot enough disk space for requested data to be transferred.
\nError 63
\nDefective or unformatted disk.
\nError 70-79
\nNetwork card issues \u2013 specific codes should be in the manual.
\nError 80
\nCycle (200k-300k prints) complete, maintenance kit needed.
\nError 82
\nReplace OPC belt (photo developer).
\nError 84
\nReplace the transfer drum.
\nError 88
\nToner is low.
\nError 122
\nFuser issue \u2013 run fuser service check.
\nError 230
\nPaper jam in duplex unit.
\nError 240-249
\nPaper jam in tray 1-5.
\nError 250
\nPaper jam in multipurpose tray.
\nError 901
\nFlash memory (with system code program) is defective.
\nError 917
\nTransfer roller issue.
\nError 920
\nFuser temperature is too low to fuse toner.
\nError 921
\nFuser temperature is below standby temperature when printer is idle.
\nError 923
\nFuser is too hot.
\nError 924
\nFuser error.
\nError 925
\nIncorrect fuser lamp installed.
\nError 927
\nPrimary fan not working.
\nError 929
\nToner sensor not working properly or cartridge defective.
\nError 930
\nIncorrect printhead installed.
\nError 931
\nPrinthead connection issues.
\nError 934
\nMirror motor circuit in printhead not working properly.
\nError 935
\nPrinthead error (sub-codes indicated by 935.XX).
\nError 936
\nMain drive motor not working properly.
\nError 939
\nCommunication with controller engine lost.
\nError 940-943
\nToner metering cycle not working properly (940-cyan, 941-magenta, 942-yellow, 943-black).
\nError 947
\nEngine board failed.
\nError 975-979
\nNetwork card failed.
\nError 980
\nCommunication failure between printer and external device.
\nError 983
\nInvalid command to connected device.
\nError 980-984
\nService one of following- system board, duplex, trays, feeder, output bin.<\/p>\n","protected":false},"excerpt":{"rendered":"
Lexmark Error Codes Error code Error code meaning Error 20 Sensor on input tray not activated \u2013 could be a jam near the sensor. Error 21 Sensor on output tray not triggered. Error 23 Paper jam near the duplex sensor. Error 24 Job not formatted correctly for the paper being used. Error 25 Sensor […]<\/p>\n","protected":false},"author":2,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"yoast_head":"\n